TEMPEST™ Accessories

REARVIEW MATERIAL MONITORING CAMERA

Easily view your material output from the comfort of your cab by using the material monitoring camera. It attaches to the top of your spreader for optimal visibility of material spread pattern. The monitor is installed inside your cab so you can ensure a smooth spread pattern and optimal material output.

6" SIDE EXTENSIONS

Increase the capacity of your TEMPEST hopper spreader with the 6″ Side Extensions Kit. The increase in capacity will vary depending on the size of your spreader; increased material capacity will vary from 0.5 to 1 yard.

Each kit contains fully stainless steel side walls and hardware to minimize corrosion and maintain a clean look. Pre-cut knockouts allow for easy installation of additional accessories and prevent the need to drill.

SPILL GUARDS

The Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, while preventing material from overflowing into the bed of the truck from off-center loading.

CENTRAL POINT GREASE KIT

The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.

* Chain Models Only (S070C, S150C, S220C, S300C, S400C & S500C)

Rolled Tarp Cover

The 70″ wide tarp seals cleanly along the edge of the hopper to protect material from getting wet. Equipped with speed bumps to keep the top screen in place and allow the tarp to easily roll to the edge of the hopper. Made of corrosion-resistant stainless steel components with few moving pieces allowing for easy install, operation, and maintenance. This tarp can be installed with already existing bolt and holes, so no drilling in required. 

* Only available for S300C, S300A, S400C, S400A, S500C, S500A

PULLOVER TARP KIT

Protect de-icing material from the elements and lock out moisture to prevent material bridging with a pullover tarp. Fitted to the hoppers dimensions, the tarp features reinforced corners and potential wear points, cutouts to prevent interference with FISHER Strobe and Worklight brackets, and a cutout for the new Rearview Material Monitoring Camera and mounting bracket. Comes standard with durable, rubber bungees for simple and secure install and removal.

* Only available for 1.5 & 2.2 cu yd models

RATCHET TIE-DOWN KIT

Positive locking mount with ratchet-strap assist provides additional in-bed stability, security, and simplifies installation for multiple vehicle types.

Hopper spreaders require bolting to the truck frame for proper operator safety.

TIE-DOWN CHAIN KIT

A Tie-Down Chain Kit provides additional in-bed stability and security. 72 inches of high-strength steel chain and binder allow you to add an extra measure of safety as you move tons of material down the road. Each kit contains four chain binder assemblies.

Hoppers require bolting to the truck frame for proper operator safety.

VIBRATOR KIT

Designed to help move stubborn material and prevent bridging, a genuine FISHER® Vibrator system will ensure that less-than-ideal material, which is prone to bridging and clogging, will not hold you up when you need to be on the move.

INVERTED V

Reduce heavy startup loads on the drivetrain and potential bridging during operations with the optional inverted V. Made of 12 gauge 201 stainless steel, the inverted V is strong and corrosion resistant, for use in highly demanding environments. The inverted V is easy to assemble and install and will provide years of trouble free use.

* Only accessory for 1.5 & 2.2 cu yd Chain Models (S150C & S220C)
* Standard on 1.5 & 2.2 cu yd Auger Models. (S150A & S220A)
* Standard on 3.0, 4.0 & 5.0 cu yd Chain & Auger Models. (S300C, S300A, S400C, S400A, S500C & S500A)

LED WORK LIGHT KIT (PRIMARY)

A genuine FISHER® LED Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20º F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.

LED WORK LIGHT KIT (SECONDARY)

A genuine FISHER® LED Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20º F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.

LED STROBE LIGHT KIT

Make sure you’re seen, day or night, with our complete hopper LED Strobe Light system. Constructed from high impact plastic, and rated beyond -20º F, this yellow LED strobe system has been designed to last and will ensure that you’re seen in even the worst of conditions.