STEEL-CASTER™ Accessories

Poly Lid Kit

POLY LID KIT

Shields de-icing material from the elements, locks out moisture to prevent material bridging and protects against material overflow while loading. Not compatible with side extension accessory.

Part Number

#72750
Regular Capacity (1.5, 2 & 3 cu yd)
#72770
High Capacity (Both 4.5 & 6.0 cu yd)
Spill Guard Kit

SPILL GUARD KIT

Available in 50″ and 70″ widths to cover the full range of STEEL-CASTER hopper spreaders, the Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, while preventing material from overflowing into the bed of the truck from off-center loading. Spill Guards not compatible with 6” Side Extensions or Poly Lid Kit.

Part Number

#81119
70" Kit
#81120
50" Kit
License Kit

LICENSE PLATE KIT

Stay legal with our quality illuminated License Plate Kit. This genuine FISHER® license plate kit has been specifically designed for your hopper and allows you to move your license plate to a spot that is visible and legally compliant.

Part Number

#99686
For All Models
Strobe Light Kit

STROBE LIGHT KIT

Make sure you’re seen, day or night, with our complete hopper Strobe Light system. Constructed from high impact plastic, and rated beyond -20º F, this yellow LED strobe system has been designed to last and will ensure that you’re seen in even the worst of conditions.

Part Number

#99494
For All Models
Vibrator Kit

VIBRATOR KIT

Designed to help move stubborn material and prevent bridging, a genuine FISHER® Vibrator system will ensure that less-than-ideal material, which is prone to bridging and clogging, will not hold you up when you need to be on the move.

*Only compatible with one 50 gal pre-wet tank kit or one 100 gal pre-wet tank kit

Part Number

#76668
For All Models*
Work Light Kit

WORK LIGHT KIT

A genuine FISHER® Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20º F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.

Part Number

#99505-2
For All Models
Work Light Kit

SECONDARY WORK LIGHT KIT

Take it up a notch with a genuine FISHER® secondary work light kit. Designed to integrate with our work light kit (99505-1), this accessory kit will provide an addition 1000 lumens of light on the opposite side of your FISHER spreader.

Part Number

#99732-1
For All Models
Side Extensions

6" SIDE EXTENSIONS

Increase the capacity of your STEEL-CASTER™ hopper spreader with this 6″ Side Extensions Kit. The increase in capacity will vary depending on the size of your spreader; increased material capacity will vary from .5 to 1 yard. Each kit contains the corner brackets, hardware and installation instructions, but does not provide the side board material.

Part Number

#99488
For All Models
Central Point Grease Kit

CENTRAL POINT GREASE KIT

The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.

Part Number

#11763
For All Models
Tie Down Chain Kit

TIE-DOWN CHAIN KIT

A Tie-Down Chain Kit provides additional in-bed stability and security. 72 inches of high-strength steel chain and binder allow you to add an extra measure of safety as you move tons of material down the road. Each kit contains four chain binder assemblies.

Hoppers require bolting to the truck frame for proper operator safety.

Part Number

#99690
For All Models
Master Accessory Harness

MASTER ACCESSORY HARNESS

Integrate all your accessories with this convenient kit. Includes all the wiring needed to go from cab to spreader, an in-cab control panel, and rear of hopper storage for accessory fuses and relays, allowing total integration of our plug and play accessories. Hydraulic model master accessory harness kit shown.

Part Number

#99627
For All Hydraulic Models
Vehicle Side Harness Kit

VEHICLE-SIDE HARNESS KIT

The Vehicle-Side Harness Kit contains components to replace harnessing on the truck or wire a second truck to operate the spreader.

Part Number

#78402
For All Models
Spreader Control Plate

SPREADER CONTROL ADAPTER PLATE

Gain the flexibility and easy installation benefits of the cup holder control mount with every spreader installation using the new Spreader Control Adapter Plate Kit. Kit contains a durable metal mounting plate and hardware.

Control Cup Holder Mount not included, order separately (#82006).

Part Number

#82018
For All Models